Home > Reviews > Modern > Revell (Germany) 1/35 scale Kit No. 03206; M48A2/A2C


Revell (Germany), 1/35 scale

Reviewed by Cookie Sewell


Stock Number and Description Revell (Germany) 1/35 scale Kit No. 03206; M48A2/A2C
Scale: 1/35 scale
Media and Contents: 185 parts (182 in medium green styrene, 2 black vinyl track runs, 1 length of wire)
Price: USD $39.95
Review Type: First Look
Advantages: First new kit in this scale of this variant in 56 years; clever molding minimizes the number of parts needed to complete the kit
Disadvantages: Parts breakdown oddly replicates the Monogram kit of 1958; “pebble” finish on not only the cast parts of the hull and turret but some plates as well; some “soft” details
Recommendation: Recommended for any ‘48 or American armor fans


Some kits take a long time to get to the market. Monogram first released its M48A2 “Big Pat” kit back in 1958, and it was quite some time before Tamiya released its M48A3 Mod B kit (No. 35120) in 1981. The Tamiya was a quantum leap ahead of the older kit in both details and assembly but had its own quirks such as being 4" too high and having all of the motorization ports in the hull to close up.

In 2013 DML began to release a new line of M48 kits with the M48A3 Mod B and a straight M48A3 kit as well as an M103A1 and M103A2 which share some of the same parts. But before they could get to the M48A2 Revell Germany beat them to the punch with two new kits, an M48A2GA2 and an M48A2/A2C. While the former kit is of a specific German variant, the latter kit also can be built as the earlier US model A2. The external differences between the A2 and upgraded A2C are a slightly larger bore evacuator (nearly impossible to see in 1/35 scale) and the deletion of the return roller based tension roller between road wheel number 6 and the drivers. (This is reflected in the directions - surprise!)

The kit corrects many of the problems with the older Monogram and Tamiya kits, but has some odd bits of its own. For reasons best known to the Germans it uses basically a very similar hull breakdown to the old Monogram kit with an upper and two lower sections to the lower hull and separate stern plates. The shapes appear closer to the profile of the actual cast hull of the 48, but also for reasons best known to themselves much of the hull surface is cast with a “pebble” finish to include the rear deck access plates, the stern access plates, and the hatches. This is too enhanced and will have to be smoothed down, which is a shame as it makes a lot of extra work for the modeler.

The details themselves are reasonably well done, and R-G has come up with an interesting way of doing the OVM tool set by molding it in one piece but with a hollow base so it then attaches to the fender to give a more three-dimensional effect than the molded-on tool sets do. It also makes it easy to replace them as you do not have to mill molded on tools off the fenders.

The canvas mantlet for the .50 caliber machine gun is nicely done, but the main mantlet appears way too taut. This will be difficult to correct without an aftermarket part as there is no “drum” to hold the gun in place and it cements directly to the turret via the mantlet cover. A Dremel Mototool may be able to put a bit of “accordion” flex into the kit’s mantlet cover if care is used. The cupola also has the early model non-domed hatch cover (albeit with the “pebble” finish).

The turret bustle rack is composed of five parts - two ends, two brackets and a center section, and while molded looks the part as it is much finer than either of the previous two kits in this area.

The wire in the kit (taped to the directions) is for antennas, but the kit indicates that the antennas are to be 75mm long or about 99 inches. That is close for an AN/VRC-47 transmit antenna but the receive antenna is 118" or about 85mm. The good news is the wire is 160mm long so you can make both antennas, but the transmit whip is actually tapered.

Note that the two jerry cans for the turret are closer to the German style ones (flip-tops) than the US ones with screw caps.

The kit provides finishing directions for five different tanks:

  • M48A2C 3rd Company, Panzer Battalion 24, Panzerbrigade 2, Braunschweig 1962 (OD, crosses, markings, black 335);

  • M48A2 2nd Company, Panzer Lehr Battalion 93, Panzerbrigade 9, Munster 1959 (OD, crosses, markings, black 213);

  • M48A2, 3-40 Armor Battalion, 1st Cavalry Division, Korea 1963 (OD, white stars, yellow triangle, B-22);

  • M48A2, 1/14 Armored Cavalry, Fulda 1962 (OD, stars, red triangle, C-40);

  • Magach (M48A2C), IDF Rafah, Sinai, Six-Day War June 1967 (sand, white barrel bands, white arrowheads on turret, IDF registration number 817648).

The decals are from Italy and I assume they are Cartograf.

Overall this kit is two steps forward and one back, and anyone interested in getting a really good A2 may want to cross-kit this model with a DML M48A3 to get a show quality result.


Sprue Layout:

A 27 Lower hull, road wheel arms, final drives, details
B 74 Wheels, shocks, bump stops, rear plate, tow hooks
C 12 Upper hull, engine grilles, heater exhaust, air cleaners
D 36 Turret shell, details, stowage bins, ventilator, hatches
G 17 Gun, mantlet, cupola, tow cables, tool set
H 16 Jerry cans, lower return/tension rollers, bustle rack center section
– 2 Black vinyl track runs
– 1 Section of wire